Sale!

Intona High Speed USB 2.0 Isolator – NF led mod + NEW*** Black Case

(1 customer review)

Original price was: $319.00.Current price is: $279.00.

Intona Industrial version / NF(noflash) led mod / color: Black

Features

  • Provides galvanic isolation to the USB bus
  • Compliant to USB 2.0 Hi-Speed (480 MBit/s)
  • Backwards compatible to Full Speed and Low Speed
  • Isolation withstands up to 2.5kVRMS
  • Advanced ESD protection (15kV IEC Air-gap Discharge)
  • Works out of the box, no drivers needed
  • Transparent to host and device: wide compatibility to all operating systems, embedded systems and devices
  • Works also with hubs and extenders
  • Supports all USB-specific transfers and modes
  • No additional round-trip latency
  • Powered by USB bus, no separate power supply
  • Ultra-quiet power rail isolation, linear regulation
  • 300mA nominal (500mA max.) output current on isolated side
  • Connectors: host-side USB-B; device-side USB-A
  • Status LED for each port showing bus state and speed
  • Impedance controlled high-speed circuit design
  • National compliances: FCC, CE, RCM, ICES-003
  • IP 54 ABS housing
  • Dimensions: 135 x 90 x 46 mm
  • Engineered and manufactured in Germany

Please read this excellent review from 6moon.com! don’t just take our word for it, but this Intona is an excellent choice to add to any system! It’s the real deal, and more than just some USB cleaner device.

Intona Review from 6moons.com

Intona Review from TNT-Audio.com

Original price was: $319.00.Current price is: $279.00.

Out of stock

Intona Industrial USB - USPS Priority - cost effective shipping price and speed.
Original price was: $319.00.Current price is: $279.00.

Out of stock

Intona Industrial USB - USPS Express - Urgent orders, faster shipping yet fairly high shipping expense.

Description

Intona Logo

High Speed USB Isolator – INDUSTRIAL VERSION (best for audio)

Now available: world’s first in-the-box solution to galvanically isolate the USB 2.0 bus in all speed modes.
Low Speed, Full Speed and High Speed.

 

Intona High Speed USB Isolator - Black
Standard Version

 

Intona High Speed USB Isolator - Industrial Black
Industrial Version (bottom) with orange colored high retention connectors

The Innovation

Previous isolators where limited to Full Speed (12 MBit/s) and Low Speed (1.5 MBit/s) transmission. This new product is capable of transmitting USB Hi-Speed (480 MBit/s) while providing full galvanic isolation of both the data and the power lines.

USB 2.0 Hi-Speed Isolator withstands up to 2.5kVRMS

This product is an ideal solution to break ground loops, avoid noise coupling and protect ports from power surges and voltage spikes in applications which require high speed USB transfers. The galvanic isolation barrier withstands potential difference up to 2500VRMS.

USB_High_Speed_Isolator_EN

Applications

  • Audiophile-grade home systems
  • Industrial automation systems
  • Measurement devices
  • Environments requiring safety insulation
  • Machine protection
  • Broadcast and Studio
  • All applications requiring clean and stable USB connections with separate grounds

FAQ

Would the Isolator improve the sound quality?

The intended purpose is complete isolation of both data and power lines. In an audio application, the resulting sound quality improvement is the effect of breaking all the noise coming from the host computer.

As this is a true industrial product, we focus primarily professional applications like automation systems, medical and research labs.
But of course, as this product is designed for low noise (research labs need this to gain dynamic range from nanovolts to kilovolts) and perfect signal integrity, we understand the demand of audio enthusiasts. We highly recommend giving it a try. If you search the web, you will find lots of positive comments and reviews about it.

Thanks to our fully equipped audio lab, we had the chance to take special attention keeping the noise of the power supply output as low as possible in the 20Hz-20kHz range and we also optimized current flow using a high-speed current sensor probe that resulted in the probably industrial-wide lowest packet noise (8 kHz and harmonics).

Following measurements are showing a typical ground loop issue (first image), cured by galvanic isolation (second image):

Intona Sound test comparison Intona Sound test comparison


I heard the Industrial version is vastly superior sounding to the Standard version. Can you comment on this?

We really cannot comment in a scientific way on the difference of Industrial vs Standard version in terms of audio quality.

Fact is:

  • both versions do the same job: isolate, repacketize, provide clean power
  • quality audio measurements confirm this

But also fact is:

  • Industrial version has full characterized parts and some better parts in sense of temperature grade (this is the reason for the name given)
  • nearly all customers seem to hear a difference in audiophile-grade environments in favour of the Industrial one

Does the Isolator affect signal quality?

The 7054-based USB Hi-Speed Isolator is a phy-level receiver/isolator/reclocker/repacketizer working at a bidirectional bandwidth of 480 MBit/s.
It receives and transmits USB data using a dedicated ULPI-transceiver, buffers and translates by our proprietary logic using FPGA technology and isolates using industry-leading RF-type isolators by Silicon Labs with least possible capacitance.
It does not translate or distort data packets like a hub but does reproduce and reclock the original data by 100%.

The circuit is a 50 ohms impedance controlled design. USB traces are matched to 90 ohms differential / 30 ohms single ended. The RMS jitter of the isolated downstream has been measured at 12.5ps.

By using a technology well known in digital communication systems called Spread Spectrum, any harmonics produced through periodic packet transmission (like 8kHz packet noise) could be eliminated.

The isolated side is supplied by our own proprietary and very careful designed DC/DC converter followed by linear regulators. The USB output voltage is generated by the Analog Devices ADP125 linear regulator.

7054_fft_output


What is the “NF” option?

Upon request we provide a special modification to the LED blinking behaviour of the 7054-based isolator. That is, swapping the “high-speed” indication by the “failure” indication.
As result, the isolator LEDs will not blink when in high speed mode but are constantly on.
You may request this version by writing “NF-option” in the paypal payment process or as an email afterwards.

Update: as of 2016-06-01, the NF option has been merged to the standard firmware. The isolator will show the connection state by blinking accordingly. After three seconds, both LEDs will be constantly on. This can be seen as a “locked” state.
With other words: all currently sold units have the NF-option on by default.


Will the Isolator pass DSD Data? Is it bit perfect? Will it pass all higher resolution PCM also?

The Isolator can reach full USB bandwidth of 480MBit/s and it will pass DSD data in a bit perfect manner without changes. This is also true for any other data format and of course for PCM audio. We have successfully transmitted 32 channels at 192kHz in both directions without failure.


Is there any customization possible, for example using a better oscillator?

What would you expect by using a “better” oscillator?

We measured 12.5ps of RMS jitter on the USB packet clock. A more or less jittery oscillator would not make any difference on this, because of the very low tuned lp-filter in the transceiver’s PLL.

We use four clocks in our design, all shifted slightly in phase and affected from natural spread spectrum of the isolator chips and other sources. This really helps to bring EMI down and to spread current peaks – e.g. to lower the packet noise.
If we would tune everything inside to least jitter, this would rise packet noise and also EMI radiation.

One need to distinguish between

  • sample clock in an ADC or DAC: low jitter is the most important, because only the right sample at the right time is the right sample
  • transmission clock of a serial system: BER (bit error rate) or eye mask to be specified
  • clock passing integrated logic: setup and hold times to be met

We decided to go for low noise, so spreading clocks and accepting inter-logic-skew was the way to go. Further, clever design of return currents and also a good and low impedance decoupling network of the power supplies are by far more important to meet your needs than looking for the oscillator.


USB PACKET CLOCK – USB 2.0 Compliance Measurements

As the Intona USB 2.0 Hi-Speed isolator is a design from scratch, not using any ready-made USB isolation chips, we were often asked about USB-compliance, signal quality and clock jitter. In the following, we have published our compliance tests for the isolated side.

For details on test setup, methodology, and performance criteria, please consult the signal quality test description at the USB-IF Compliance Program. We tested using a LeCroy Serial Data Analyzer. You can find the corresponding test sheet here.

USB Test No. Description Requirement Result Conclusion
EL_21 Sync Field X = 31 X = 31 Passed
EL_22 Inter-packet Gap #2 X = 8 bits < X < 192 bits same as host Passed
EL_23 Inter-packet Gap #1 88 bits < X < 192 bits same as host Passed
EL_25 EOP Width X > 7.5 bits X = 7.97 bits Passed
EL_33 Chirp Response time X < 100us X = 50.3us Passed
EL_34 Chirp JK Duration 40us < X < 60us X = 50us Passed
EL_35 Chirp JK->SOF time 100us < X < 500us X = 101.1483us Passed
EL_39 Host Suspend time 3.0ms < X < 3.125ms X = 3.052ms Passed
EL_41 Host Resume time X < 3ms X = 1.369us Passed
EL_55 SOF EOP Width X > 40 bits X = 40.1 bits Passed
EL_28 Chirp-K Latency 2.5us < X < 6.0ms X = 3.02us Passed
EL_29 Chirp-K Duration 1.0ms < X < 7.0ms X = 2.76ms Passed
EL_31 Device Turn On X < 500us X = 573ns Passed

Table 1: USB Compliance Electrical Test

Description Result Conclusion
Signal eye see diagram Passed
EOP width 7.97 bits Passed
Measured signaling rate 479.9464 MHz Passed
Rising Edge Rate 1233.48 V/us (518.86 ps equivalent risetime) Passed
Falling Edge Rate 1256.71 V/us (509.27 ps equivalent risetime) Passed

Table 2: USB Near End High Speed Signal Quality Test of Isolated Side

Description Range Min Range Max RMS
Consecutive Jitter -31.061ps 30.560ps 12.512ps
Paired JK Jitter -30.454ps 32.848ps 8.833ps
Paired KJ Jitter -41.908ps 32.871ps 9.087ps

Table 3: Additional Information (Isolated Side)

Overall result: pass!

Signal Eye (Isolated Side):

7054_SQ_DS_Iso_Eye 7054_SQ_DS_Iso_rpt1 7054_SQ_DS_Iso_rpt2

Please read the following PDF for more information on it’s ability to suppress the known 8Khz USB Packet noise issue far better than most devices.

USB_High_Speed_Isolator_EN

Additional information

Weight 1 lbs
Shipping Type - USPS Priority or Express

USPS Priority, USPS Express

1 review for Intona High Speed USB 2.0 Isolator – NF led mod + NEW*** Black Case

  1. Christian (verified owner)

    Got this to clean up the USB output of my Mac mini, which is known to be bad, and feed a clean signal into my USB path. So far it has been working well. No compatibility issues, plug and play as long as your downstream device (DDC or DAC) doesn’t need more than 300 mA.

Add a review

Your email address will not be published. Required fields are marked *

You may also like…